How to add a touch screen to your Raspberry Pi projects

Monitor with attached keyboard and mini screwdriver

You simply want a Raspberry Pi, a contact display and a screwdriver.

Adrian Kingsley Hughes/ZDNET

You in all probability already know How numerous are Raspberry Pi computer systems. However you will not actually get to expertise the true energy and suppleness of this platform till you add a monitor.

And never any previous display, however a contact display.

Here is what it is advisable do to construct a contact display laptop with a Raspberry Pi.

First, you want a file Raspberry pie. That is simpler mentioned than carried out since they’re in it Briefly providehowever store round and you may doubtless discover one (here is ZDNET’s tip for The place to purchase a Raspberry Pi 4 and its alternate options).

You probably have an older Raspberry Pi 3, you should utilize it with this display.

additionally: These are the three Raspberry Pi equipment that I’ve to personal

That is mine – it is 8GB Raspberry Pi 4B.

Raspberry Pi 4 in a box

Adrian Kingsley Hughes/ZDNET

You then want a present.

There are a variety of shows, however the one I am utilizing right here is the one Official Raspberry Pi 7 inch 800 x 480 pixels contact display.

This, plus a Phillips screwdriver, is the naked minimal you want, however I went just a little additional and added a case as effectively.

The case helps defend the Raspberry Pi and display from harm, and makes it really feel like a correct laptop relatively than a homebrew mission.

Now that you’ve got all of the components you want, here is the method for including the contact display to your Raspberry Pi.

1. Join the all-important ribbon cable

A finger next to where the ribbon cable connects to the display controller on the left edge

Join the ribbon cable to the monitor console.

Adrian Kingsley Hughes/ZDNET

Mounting the monitor is fairly simple, however the first half can be the difficult half as a result of it includes utilizing the tiny ribbon cable.

To attach the ribbon cable to the connector on the show, first discover the show connector. There’s a small grey plastic tab on this connector that ought to slide again to permit the ribbon cable to be put in. Push the ribbon cable in so far as it’ll go after which press the grey tab again into place to safe the ribbon cable.

additionally: I’ve simply solved one among my greatest complications with my Raspberry Pi

The ribbon cable in my equipment had a blue facet, and the directions mentioned to have that facet going through the circuit board. The ribbon cable could also be totally different, so verify your directions.

2. Join the Raspberry Pi to the show console

screwdriver on the edge of the display board

Connect the Raspberry Pi to the show board.

Adrian Kingsley Hughes/ZDNET

Subsequent, I mounted the Raspberry Pi to the board, and connected it with the 4 screws.

You need not tighten these screws!

3. Join the jumper wires

Four wires of different colors are connected to the side of the monitor's control panel

Connecting wires provide energy to the monitor.

Adrian Kingsley Hughes/ZDNET

I additionally wanted to attach 4 jumper wires to the monitor management board. It would not matter which shade you connect with, however it is advisable know which one since you’ll want to attach them to the suitable pin in your Raspberry Pi in a bit.

For reference, listed here are the 4 connectors and which pin on the Raspberry Pi they want to connect with:

  • 5V -> Pin 2 or Pin 4
  • GND -> pin 6
  • SDA (information) -> pin 3
  • SCL (clock) -> pin 5

Trying on the Raspberry Pi board with the writing in the proper path, pin 1 is on the 40-pin connector alongside the highest on the underside left, and pin 40 is on the highest proper.

4. Join this essential ribbon cable to the Raspberry Pi

The ribbon cable is attached to the left edge of the Raspberry Pi

Join the opposite finish of the ribbon cable.

Adrian Kingsley Hughes/ZDNET

Keep in mind the ribbon cable you linked to the monitor console?

Now it is time to join the opposite finish to the Raspberry Pi. The method is identical for connecting it to a show controller.

5. Match all the things into the case

A screwdriver closes the transparent case containing the Raspberry Pi and the display

Put all the things within the case.

Adrian Kingsley Hughes/ZDNET

Subsequent, I inserted your complete set into the case. It took just a little fiddling to get the display into the case correctly, however all the things appeared to fall into place as soon as the screws had been put in. You may inform when it’s in place appropriately as a result of the ports will line up with the cutouts.

Clear case showing cutouts for the ports

What does it appear to be when all the things traces up.

Adrian Kingsley Hughes/ZDNET

Once more, you need not overtighten these screws.

6. You are carried out!

You’ve got added a contact display to your Raspberry Pi! Energy in your Raspberry Pi and replace the software program, and also you’re able to take your initiatives to the subsequent degree.

Leave a Comment